SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

eurocol
233 EUROSOL CONTACT

233

Contact adhesive, very high immediate contact bonding power. Contains solvents.

233_eurosol contact.jpg
  • safety data sheet_eurocol_233_uk.pdf

    safety data sheet_eurocol_233_uk.pdf

  • pdf-product-specification.pdf

    pdf-product-specification.pdf

Product Typification

Two-sided contact adhesive.
Basis : Synthetic rubber in solvent.
Colour : Cream.
Consistency : Thick liquid.

Product advantages:
  • Solvent-contained, thermally reactivable contact adhesive with very high initial contact bonding power for temperature resistant contact adhesion of a great variety of materials such as metal, glass, ceramic, plastics (ABS, PVC, Acrylic) wood, leather, hardboard, rubber etc.
  • In floor covering installation for wooden skirting boards (rubber) stair nosings, groove profiles, floor covering.
  • Also used for installation of homogenous vinyl, rubber, leather and cork floor coverings, linoleum according to floor covering manufacturer‘s instructions.
  • GISCODE S 1. Please check safety data sheet!
  • High initial adhesion strength
  • Fast drying
  • High final bond strength
  • Favourable spreading capacity 

Performances

Consumption : 200 - 250 g/m², when fixed two-sided.
Curing : 24 hours.*
Flammability : 233 Eurosol Contact contains a highly flammable solvent. Do not smoke during application, do not expose to open flame, extinguish pilot lights and ventilate thoroughly.
Specific weight : 0.85 kg/l.

Application

Application:

For the two-sided installation of:

  • rubber
  • homogeneous PVC
  • plastic profiles
  • linoleum
  • leather, board, cork
  • carpet
  • foam-rubber. 

Working Process

Tools : Adhesive spreader A4 or brush.
Open time : 2 hours.*
Waiting time : 5-15 minutes.*
Application temperature : Recommended 3 grd above dew point temperature.
Curing : 24 hours.*
Storage : Protect against high temperatures.
Shelf Life : Approx 12 months, in unopened packaging. After use close the open packaging well.
Cleaner : Acetone.
Sensitive to frost : Yes.
Remarks : 

Relevant norms and regulations of the branch are to be respected. Outside Germany relevant national regulations are to be applied which have to be known by the user.

The instructions of the respective profile manufacturers must be observed, especially when gluing stair nosing edges. In case of doubt, the adhesive side should be degreased/cleaned of exudates.
In high humidity, a moisture precipitation can form on the drying adhesive near the dew point temperature, which then hinders the contact bonding. In such cases, briefly apply warm air to the adhesive surfaces.
Contains highly volatile, flammable solvents. In combination with air, the adhesive could turn into an explosive mixture which could lead to a high concentration especially at the lowest point of the room! Please pay attention to the
safety data sheet. Ensure sufficient ventilation of the work rooms!
We refer to the Ordinance on Hazardous Substances §16. Please check the possibility of using solvent-free products for your installation work e.g. Eurocol 650 Eurostar Fastcol


* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
200 - 250 g/m², when fixed two-sided.

Substrate:
  • 233 Eurosol Contact is suitable for any type of subfloor that has a good tensile and compression strength.
  • The subfloor should also be clean, permanently dry and free from grease and dirt, according to the requirements of BS 8203 or DIN 18 365.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 


User manual:

Before use, temper the product according to the processing conditions.

  • Stir the adhesive well before use.
  • Apply the adhesive on the subfloor and back of the material to be fixed with a brush or adhesive spreader A2.
  • Allow the adhesive to dry for 15 minutes (depending on temperature, relative humidity, subfloor and material).
  • Place the material on the subfloor and press, roll or hammer firmly.
  • After mixing adjustments are not longer possible.
  • Remove fresh spots immediately with white spirit.
  • Do not smoke during application, do not expose to naked flame, extinguish pilot lights and ventilate thoroughly.

Working conditions:
Required surrounding temperature : 18° - 23 °C.
Material and subfloor temperature : min. 15° - max. 20 ºC.
Relative humidity : 40 - 80%.

Underfloor heating systems:
233 Eurosol Contact can be applied on underfloor heating systems. The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier. Turn off the heater 24 hours before application. Do not heat again until at least 24 hours after installation, in steps of 5 °C per day.





Environment and health

GISCODE : S1
LEED : VOC 663 g/l
DGNB : VOC 79 %
Hazard Class : 3-5c ADR/VLG-adhesives/ UN-code 1133.
Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155. Keep out of reach of children. Do not eat, drink or smoke while processing the product. Only give completely empty containers for recycling. Bound material residues can be disposed of as household waste.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.
Substances causing allergy : Contains Rosin.Can cause allergic reactions.





Articles

Article   Definition Packaging EAN-codeshipping unit
233Eurosol Contact10 kg metal drum8 710345 23305742/pallet
233Eurosol Contact5,5 kg metal drum8 710345 23309570/pallet
233Eurosol Contact0.65 kg metal drum8 710345 2330718 drums/box, 392 drums/pallet