SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

Forbo Websites

Select a division
Forbo Group
Forbo Flooring Systems
Forbo Movement Systems
CONTACT FAQ

eurocol
308 WALLDESIGN FINISH

308

Transparent protective layer and colour intensifier for 307 WallDesign.

308 1kg gerecyclede fles rgb.jpg
  • pdf-product-specification.pdf

    pdf-product-specification.pdf

Product Typification

Transparent protective layer and colour intensifier for 307 WallDesign.
Basis : Solvent-free transparent finishing coat based on acrylic dispersions.
Consistency : Liquid.

Product advantages:
  • Ready to go
  • Colour-deepening effect
  • Light shine
  • Easy to process on the wall
  • Very economical consumption

Performances

Consumption : Approx. 50 g/m² per layer
Flammability : Non-flammable.

Application

Application:
Ready-to-use product for applying a transparent protection and colour deepening to 307 WallDesign.

Working Process

Tools : 807 Microfibre roller 9 mm
Storage : Store in a cool and frost-free place (between 5⁰ - 25 ⁰C)
Shelf Life : Minimum 12 months in unopened packaging.
Drying : 24 hours after the last layer.
Sensitive to frost : Yes.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
Approx. 50 g/m² per layer

Substrate:
  • Before applying 308 WallDesign Finish, 307 WallDesign must be applied by following the steps in the relevant instructions for use and allowed to dry completely.
  • Always consult our technical product information sheets beforehand. In case of doubt about the applications to be made, contact our Technical Advice Department in advance on T +31 (0)75 627 16 30 .


User manual:
  • Ensure a room temperature of approx. 15° – 20 °C. Shake before use.
  • 308 WallDesign Finish is very easy to apply with a clean 9 mm microfibre roller. This finish gives the surface a light satin sheen and a deeper colour. Tip for a lint-free roller: stick a piece of tape to the wall before painting and roll the new roller over it a few times.
  • Pour 308 WallDesign Finish into a clean bucket or paint tray. Apply small amounts of the finish from the bottom upwards. Apply the liquid uniformly and distribute it over the surface until the liquid is evenly absorbed into the surface without streaking. If necessary, polish the 308 WallDesign Finish you’ve just applied with a microfibre cloth.
  • By applying several layers of finish, the surface is better protected and gets a slightly water-repellent surface. Apply several thin layers wet in wet. The applied layer may also be dry before a next layer is applied.
  • The drying time is 24 hours after applying the last layer.
  • For processing tips, see the WallDesign video and product sheets.
  • We recommend using 312 Conditioner for cleaning and maintenance. This product creates a protective film and reduces the adhesion of dirt to the surface. If used regularly, it preserves the appearance of the wall (with no gloss effect). Never not use chlorine or bleach!
  • Dispose of product residues and cleaning water according to the local environmental regulations and do not pour into drains.
  • Avoid contact with eyes and skin and use suitable protective equipment (see safety data sheet).

Processing conditions:
Desired ambient temperature : 15° - 20 °C.
Relative humidity : 40 - 70%.





Environment and health

Hazard Class : None.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.


Articles


ArticleDefinitionPackagingEAN-code
308WallDesign Finish Bottle of 1 kg8 710345 308106
308WallDesign FinishOuter packaging 12 x 1 kg bottles 8 710345 308120