SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

Forbo Websites

Select a division
Forbo Group
Forbo Flooring Systems
Forbo Movement Systems
CONTACT FAQ

eurocol
777 FLEXICOL

777

Flexible powder tile adhesive for bonding ceramic wall and floor tiles, mosaic and flat dark-coloured natural stone. Can be used on almost any cement-based substrate, concrete, existing tiling, underfloor heating, etc.

777-flexicol.jpg
  • epdfeica-777 flexicol uk.pdf

    epdfeica-777 flexicol uk.pdf

  • dop-declaration-uk.pdf

    dop-declaration-uk.pdf

  • 777-safety data sheet uk.pdf

    777-safety data sheet uk.pdf

  • pdf-product-specification.pdf

    pdf-product-specification.pdf

  • Product Typification
    Flexible cement-based tile adhesive.
    Basis : Cement-based powder with additives and a high synthetic binder content to be mixed with water.
    Colour : Grey and white.

    Product advantages:
    • Suitable for almost all subfloors
    • High initial adhesion strength
    • High final bond strength
    • Easy to apply
    • Permanent flexible
    • Low chromate

  • Performances
    Aging : 777 Flexicol does not deteriorate with age.
    Classification : C2TE according to NEN EN 12004. A cement-based tile adhesive with an increased slip resistance and an extended open time.
    Consumption : 1.2 - 3.5 kg/m², depending on the smoothness of the subfloor and type of tile.
    Curing : 24-48 Hours, depending on the subfloor and temperature. Lower temperatures will slow down the bonding time.
  • Application
    • For the flexible fixing of wall and floor tiles on almost all subfloors (e.g. wood, concrete, old tiles etc.).
    • Also very suitable for fixing wall tiles on uneven subfloors (e.g. lime-sand stone) and for fixing non-absorbent tiles on non-absorbent walls.
    • Not suitable for outdoor applications and in case of water pressure (constant moisture-pressure). Use 705 Watertight Tile Adhesive, 711 Uniflex or 795 Uni-Quick.
    • Because of the possibility of discoloration, 777 Flexicol grey is not suitable for fixing glass-mosaic and light-coloured natural stone, such as marble. For these applications we recommend 777 Flexicol white.

  • Working Process
    Open time : Place the tiles within approx. 15 minutes into the wet adhesive, depending on the subfloor and temperature.
    Mixing ratio : 25 kg 777 Flexicol to approx. 6 litres of water.
    Waiting time : After mixing with water wait for a few minutes, stir once again and apply the mortar on the subfloor.
    Application temperature : From 5° to 25 °C (temperature of the surrounding as well as the subfloor).
    Processing time : Apply the mixture within 90 minutes.
    Curing : 24-48 Hours, depending on the subfloor and temperature. Lower temperatures will slow down the bonding time.
    Storage : Store cool, dry and in closed packaging.
    Shelf Life : 12 Months, in unopened packaging. After use close the open packaging well.

    * The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

    Consumption:
    1.2 - 3.5 kg/m², depending on the smoothness of the subfloor and type of tile.

    Substrate:
    • The subfloor must have a good tensile and compression strength. The subfloor should also be smooth, dry and free from grease, dirt and dust, according to the requirements of DIN 18 352.
    • Wooden floors, made of floorboards, should be sufficiently supported underneath (distance between the beam maximum 60 cm). To attain a fixed construction screw water-resistant plywood (minimum 12 mm thickness) on top of this layer. Thereafter apply 099 Dispersion Primerand primer. Maximum tile size 30x30 cm.
    • For self-levelling anhydrite floors use our 725 Alphycol. 
    • In advance always seek our technical data sheets. In doubt about the application ask for technical advice.


    User manual:
    • Add 25 kg of 777 Flexicol to approx. 6 litres of cool and clean tap water and stir the mortar for one minute, by using an electric stirrer (approx. 600 rpm), to a smooth and homogeneous mixture.
    • After stirring wait for a few minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive spreader (see spreading capacity/notched spreader).
    • Place the tiles within approx. 15 minutes with a shuffling movement into the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints.
    • Apply the mixed adhesive within 90 minutes. Do not add extra water!
    • Floor tiles are passable after 24 hours.
    • Under normal circumstances, i.e. a temperature of 20 °C and a relative humidity of 65%, the joints may be filled after minimum 24 hours.

    Spreading capacity/notched spreader for powder tile adhesives:

    The smoothness of the subfloor and type of tile are determining for the adhesive spreader to be used. Selection of the notched spreader should be made in such way that a minimum adhesive contact of 80% is guaranteed (equally divided over the back of the tile). Check the adhesive contact regularly.

    Spreader no. 19, 4x4 mm : Spreading capacity approx. 1.2 kg/m²
    Spreader no. 12, 6x6 mm : Spreading capacity approx. 2.0 kg/m²
    Spreader no. 13, 8x8 mm : Spreading capacity approx. 2.7 kg/m²
    Spreader no. 14, 10x10 mm : Spreading capacity approx. 3.5 kg/m²




  • Quality and guarantee
  • Environment and health
    MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.


  • Articles
    ArticleDefinitionPackagingEAN-code
    777Flexicol 25 kg bag

    		grey
    		8 710345 777018 

    		white
    		8 710345 777209