• High-quality, universal, very low-stress setting, self-levelling compound based on alpha-hemihydrate.
• For very high loads.
• For levelling mineral substrates, also less stable substrates, ceramic tiles, natural stone coverings, terrazzo, screwed wood-based panels (V100 P4 - P7, OSB 2 - 4) and prefabricated screeds as well as mastic asphalt, prefabricated screeds, mastic asphalt and on approved Eurocol decoupling boards (e.g. 823 Eurofloor Reno).
• Can be used in layer thicknesses up to 20 mm, on mastic asphalt up to 8 mm, on decoupling boards (e.g. 823 Eurofloor Reno) up to 10 mm.
• For subsequent flooring work and the laying of parquet.
• Also for the production of Eurocol FloorDesign floors in combination with Eurocol pigment powder 390 FloorColouring and Eurocol Surface Finish.
• Pumpable up to 75 m hose length.
• Squeegeeable.
• No ettringite formation on calcium sulphate screeds.
• Chromate-free, therefore skin-friendly.
• The product can be used on underfloor heating and is suitable for use with chair castors according to DIN EN 12529.
• For interior use.
• Low emission, low solvent according to Blue Angel UZ 113.
• Very low-emission installation material, certified according to EMICODE EC 1 Plus.

• The substrate must be permanently dry, pressure- and tension-resistant, free of cracks and dust, even, and free of adhesion-reducing layers.
• Adhesion-reducing layers, old material residues must be removed by suitable mechanical means in accordance with the specifications of DIN 18365/DIN 18356.
• Cracks or joints (except for structural expansion joints) are to be closed with Eurocol grouting compounds Europlan 913 Silicate.
• Old hard-wearing floors, such as ceramic tiles, terrazzo, stone floors, must be cleaned professionally with Eurocol 891 Euroclean Basic and sanded to a matt finish after drying.
• Prime with a Eurocol primer adapted to the substrate and the expected layer thickness of the leveling compound. Allow the applied primer to dry thoroughly.
• Appropriately dimensioned Eurocol edge strips must be placed towards rising building components.
• Level out coarse unevenness in advance with stable filling compound. After complete drying, prime the surface again.
• In case of defects, concerns must be raised in writing.

• When mixing 920 Europlan Alphy ensure that tools are always clean and free from cement residues.
• In case of preparation by hand add 25 kg of 920 Europlan Alphy to 5.5 - 6 litres of cool and clean tap water. Follow the exact water ratio. 
• Stir the mortar, using an electric stirrer, to a smooth and homogeneous mixture.
• Wait for approx. 5 minutes and stir the mortar once again, with a low rpm. ·
• Apply the mortar within 30 minutes on the floor with a trowel or notched squeegee in a minimum layer thickness of 2 mm. ·
• When pumping, adjust the mixing device so that a correct amount of cold and clean tap water is added. Determine the spreading dimension! Also flush machine and hoses during breaks to prevent hardening within the machine system. Please consult your pump manufacturer.
• Protect fresh levelling compound layers against draft and direct sunlight.
• In the case of multi-layer levelling, apply an intermediate primer to the fully set first levelling compound before applying the second levelling compound. Alternatively, use a levelling compound formulated for the required layer thickness in order to apply the levelling compound in one operation.
• It is not recommended to sandpaper or prime the dried levelling compound layer.
• If necessary to sandpaper the applied levelling compound layer make the floor dust-free with an industrial vacuum cleaner. When necessary prime the subfloor with a sutitabel Eurocol primers.

When mixing the levelling compound, make sure that the tools are always clean and free of cement residues.

Working conditions:
Required surrounding temperature  : minimum 18 °C.
Temperature subfloor : minimum 15 ºC.
Relative humidity : 35 - 75%, required < 65%.

Underfloor heating systems:
920 Europlan Alphy can be applied on underfloor heating systems. The startprotocol of the floorheating needs to be completly executed in accordance with the directives of the supplier. Turn off the heater 24 hours before application. Do not heat again until at least 24 hours after application, in steps of maximum 5 °C water temperature per day.