Highly durable, fast curing, water- and solvent-free, two-component PUR adhesive.

For laying rubber floor coverings in tiles with rough backings, PVC- and recycled PVC floor coverings (tiles and panels), metal, ceramic, wood.

Bonding is carried out on standard-compliant, fully levelled substrates like absorbent and non-absorbent mineral-based subfloors, sanded mastic asphalt, wood composites, dry screeds which are permitted for floor covering installation. Reactive primers must be sprinkled with quartz sand.

• Water-resistant
• Moisture-resistant and weatherproof
• Heavy duty resistant
• Non-flammable
• Extremely high final bond strength
• Temperature resistant from -40 °C to +150 °C 

Can be used on underfloor heating systems. 

For indoor use only.

Very low emission certified EMICODE EC 1 Plus.

Emission-tested construction product according to DIBt principles.

For the installation of:

• rubber floor covering
• vinyl floor covering
  
• concrete
  

• The substrate must be pressure- and tension-resistant, permanently dry, free of cracks and dust, even and free of layers that reduce adhesion.
• Adhesion-reducing layers, old material residues must be removed by suitable mechanical measures in accordance with the specifications of DIN 18365/DIN 18356/BS 8203.
• Old fixed floors, such as ceramic tiles, terrazzo, stone floors, metals, must be professionally cleaned and sanded matt after drying.
• Cracks or joints (except structural expansion joints) are to be closed with Eurocol grouting compounds Europlan 913 Silicate.
• Prime porous, rough surfaces and cement screeds that are crumbling on the surface with 021 Euroblock Reno LE. If alkaline moisture or construction moisture is present and the stony subfloor is above groundwater-level apply two coats 021 Euroblock Reno LE. In order to create a sufficient bonding bridge for later application of the adhesive, the filled surface should be sprinkled with fine, dried sand.
• As the adhesive has a strong filling effect, there is generally no need to apply a filler.
  If necessary, use Eurocol 140 Euromix PU Pro or Eurocol 910 Europlan PU Duo.
  In order to create a sufficient bonding bridge for later application of the adhesive, the filled surface should be sprinkled with fine, dried sand, such as 846 Europlan Sand (quartz sand), or the filled surface should be sanded matt.
• In the event of defects, objections must be made in writing.
• In advance always seek our technical data sheets. In doubt about the application ask for technical advice.

Before use, temper the product according to the processing conditions.

The adhesive will also bond at lower temperatures, but will be less easy to apply. Besides the bonding of the adhesive will slow down and the adhesion on smooth surfaces, in particular metal, will decrease strongly. Check in advance if the rubber floor covering is ready for installation or has to be sandpapered beforehand.

Directions for use:

• Add component B to component A.
• Stir thoroughly, using an electric stirrer, to a smooth and homogeneous mixture.
• Only mix as much adhesive that can be used within the mentioned pot life.
• Apply the mixture immediately on the subfloor with the recommended adhesive spreader. The quantity of adhesive depends on material and subfloor.
• When fixing a floor covering with a stud back make sure to apply sufficient adhesive, so the hollow sections between the studs are sufficiently filled with adhesive. Due to the large variety of backings it is not possible to indicate a standard adhesive spreader and spreading capacity.
• When laying parquet, ensure that the parquet is approx. 1.5 cm away from the wall.
• Place the floor covering directly into the wet adhesive. A short waiting time within the open time of 30 minutes improves the final adhesion a little. In case of topping edges place a load during 6 hours.
• To avoid accumulation of the adhesive do not walk on the fresh applied floor covering. Always walk behind the roller during rolling.
• Repeat pressing and roling after 1 - 2 hours.
• Remove fresh adhesive spots immediately with white spirit. Clean tools immediately after use with white spirit.