• Elastic, shear-resistant (ISO 17178), water and solvent-free parquet adhesive based on SMP, hardens without shrinking.
• For installation of strip parquet, mosaic parquet elements*, multi-layer and solid parquet, lamparket products* width to thickness ratio of less than 5:1, permitted solid floor boards >= 15 mm thickness (thickness ratio of less than 1:7), for edge lamella parquet with a minimumthickness of 16 mm.
• Also suitable for the wood species bamboo, smoked oak and especially for surface-treated parquet.
• Colouring in wood colour light brown.
• Bonding is carried out on standard cementitious and calcium sulphate-bound screeds, on wooden composites which meet the requirements for parquet installation, fully sanded mastic asphalt, gypsum-boards suitable for installation of parquet and on Eurocol insulation mats (e.g. 823 Eurofloor Reno, 820/821 Eurofloor comfort, 804 Eurofloor Reno Fleece).
• Also usable on non-absorbent surfaces (e.g. fixed and cleaned ceramic and natural stone tiles, artificial stone, metals).
• The adhesive is characterized by a long installation time.
• Floating of the parquet elements is greatly reduced due to the high suction adhesion. Therefore especially suitable for large format parquet.
• Easy to remove from lacquered surfaces, therefore particularly suitable for surface-treated parquet types.
• For high step-sound improvement.
• Usually no primer necessary.
• Suitable over underfloor heating systems.
• Easy to remove from varnished surfaces.
• Sanding and sealing after 48 hours.
• For indoor use only.
• Very low VOC emission. EMICODE EC 1 Plus.
• Emission-tested construction product according to DIBt principles
• Declared by baubook, "ecological building product".
• Low emission, low solvent according to Blue Angel UZ 113.

For installation of strip parquet

• solid parquet 
• multi-layer parquet
• mosaic parquet elements*
• for edge lamella parquet with a minimum thickness of 16 mm
• lamparket products* width to thickness ratio of less than 5:1
• permitted solid floor boards >= 15 mm thickness (thickness ratio of less than 1:7)

Also suitable for the wood species bamboo, smoked oak.

• The substrate must be pressure- and tension-resistant, permanently dry, free of cracks and dust, even and free of layers that reduce adhesion.
• Adhesion-reducing layers, old material residues must be removed by suitable mechanical measures in accordance with the specifications of DIN 18356.
• Old fixed floors, such as ceramic tiles, terrazzo, stone floors, metals, must be professionally cleaned and sanded matt after drying.
• Cracks or joints (except structural expansion joints) are to be closed with Eurocol grouting compounds Europlan 913 Silicate.

Recommended primers:

• When laying large-format parquet elements, it is necessary to ensure that the laying surface is even. Use levelling compounds suitable for parquet flooring.
• In case of defects, concerns must be reported in writing.

• Before use, temper the product according to the processing conditions.
• Remove any ”skin” on top of the adhesive, do not stir or mix any skin with adhesive.
• Apply the adhesive evenly to the substrate with a toothed strip adapted to the installation and the substrate roughness. If necessary, the toothed strip can be adjusted accordingly to achieve sufficient grooved back wetting. In the case of long elements, the toothed strip must be enlarged accordingly.
• When laying the parquet, do not press glue between the elements to prevent adhesive marks in the joints and prevent possible interactions with the parquet lacquer. *
• Installed materials must be immediately rolled on using a hand roller or cork rubbing board.
• Since with reaction adhesives a slight "floating" of the material to be laid cannot be avoided, the laid surface must not be walked on within the first 2 hours. If it is necessary to walk on the surface, load distribution plates must be used to avoid crushing of the adhesive.
• When working on parquet, ensure that the installed parquet is approx. 1.5 cm away from the wall.
• If necessary, the glued parquet must be weighted down during the entire setting time, especially in the case of long parquet elements.
• After a setting time of approx. 2 hours, roll the floor once again with a multi-section roller.
• Sanding and sealing is possible under standard conditions after setting of the adhesive. Sanding is delayed at low temperatures, relativ humidity and high adhesive application rate by up to 2 days.

When installing parquet without tongue and groove joints, use only approved Eurocol parquet lacquers and care products work. Interactions cannot be excluded when using unknown, non-approved systems.

Recommended parquet finishes and oils:

With this adhesive, standard-compliant parquet can also be glued directly onto non-sprinkled, specially approved Eurocol reaction resin primers or approved dispersion primers.

The adhesive has excellent adhesion properties in combination with most types of wooden floors. Due to the large variety of wooden floors, in case of doubt, we recommend to carry out adhesive tests before processing, especially in the case of exotic woods.

Due to the elastic bonding, care must be taken to reduce side gluing when using water-based parquet sealants.

When gluing critical parquet formats to underfloor heating (e.g. solid plank, bamboo, 16 mm vertical lamella) a stabilising primer with approved Eurocol reaction resin primers** is necessary.

Processing conditions: 

at least 15 °C floor temperature,
at least 18°C material and room temperature,
35-75% relative humidity, recommended <65%.