SelectYourLanguage

Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2
Pulldown 2

Forbo Websites

Select a division
Forbo Group
Forbo Flooring Systems
Forbo Movement Systems
CONTACT FAQ

eurocol
795 UNI-QUICK

795

Fast drying cement-based tile adhesive.

795-uni-quick.jpg
  • 795-safety data sheet uk.pdf

    795-safety data sheet uk.pdf

  • epdfeica-795 uni quick uk.pdf

    epdfeica-795 uni quick uk.pdf

  • dop-declaration-uk.pdf

    dop-declaration-uk.pdf

  • pdf-product-specification.pdf

    pdf-product-specification.pdf

Product Typification

Fast drying cement-based tile adhesive.
Basis : Cement-based powder with additives to be mixed with water.
Colour : Grey.
Consistency : Powder.

Product advantages:
  • Passable after 3 hours at 20 °C
  • Moisture- and frost-resistant
  • Easy to apply
  • For wall and floor 
  • For in- and outdoor use
  • Suitable for fixing tiles with a moisture-absorption capacity of 1% or less
  • High initial adhesion strength
  • High final bond strength
  • Does not deteriorate with age
  • Low chromate

Performances

Aging : 795 Uni-Quick does not deteriorate with age.
Classification : Flexible cement-based tile adhesive, which as far as final bond strength, moisture- and frost-resistance complies with C2F, according to NEN EN 12004.
Consumption : 1.2 - 3,5 kg/m², depending on the smoothness of the subfloor and type of tile.
Curing : 3-5 Hours, depending of the subfloor and temperature. Lower temperatures will slow down the drying time.

Application

  • For a fast fixing of tiling, mosaic and dark-coloured natural stone on solid floors.
  • Suitable for application in the so-called “wet areas”, swimming pools and outdoor use.
  • Also suitable for tiles with a moisture-absorption capacity of 1% or less, tested in accordance with EN 99.
  • Because of the possibility of discoloration not suitable for fixing glass-mosaic and light-coloured natural stone, such as marble. For these applications we recommend 711 Uniflex or 681 Marmercol. 

Working Process

Open time : Place the tiles within 10 minutes into the wet adhesive, depending on the subfloor and temperature.
Mixing ratio : Add 25 kg of 795 Uni-Quick to 5-5.5 litres of water. 5 kg of 795 Uni-Quick to 1-1.1 litres of water.
Waiting time : After mixing with water wait for a few minutes, stir once again and apply the mixture on the subfloor.
Application temperature : From 5° to 25 °C (temperature of the surrounding as well as the subfloor).
Processing time : Use within 20 minutes after mixing.*
Curing : 3-5 Hours, depending of the subfloor and temperature. Lower temperatures will slow down the drying time.
Storage : Store cool and dry in unopened packaging.
Shelf Life : 9 Months, in unopened packaging. After use close the open packaging well.

* The mentioned values have been established in our laboratory and must be considered as guidelines in view of possible variations in climatic circumstances, subfloor compositions and layer thickness.

Consumption:
1.2 - 3,5 kg/m², depending on the smoothness of the subfloor and type of tile.

Substrate:
  • The subfloor must have a good tensile and compression strength. The subfloor should also be smooth, dry and free from grease, dirt and dust, according to the requirements of DIN 18 352.
  • When using the adhesive outdoors apply two layers of 730 Isoflex. Also remove all old ceramic finishing.
  • In advance always seek our technical data sheets. In doubt about the application ask for technical advice. 


User manual:
  • Add 25 kg of 795 Uni-Quick to 5-5.5  litres of cool and clean tap water and stir the mortar for 1 minute, by using an electric stirrer (approx. 600 rpm), to a smooth and homogeneous mixture.
  • After stirring wait for a few minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive spreader (see spreading capacity/notched spreader).
  • Press the tiles within 10 minutes with a shuffling movement into the adhesive. Check regularly to ensure that the entire back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints.
  • Apply the mixed adhesive within 20 minutes. Do not add extra water!
  • Under normal circumstances, i.e. a temperature of 20 °C and a relative humidity of 65%, the joints may be filled after 3-5 hours.

Spreading capacity/notched spreader for powder tile adhesives:

The smoothness of the subfloor and type of tile are determining for the adhesive spreader to be used. Selection of the notched spreader should be made in such way that a minimum adhesive contact of 80% is guaranteed (equally divided over the back of the tile). For outdoor purposes this contact must be 100%. Also counts for heavy-duty indoor floors, e.g. store and warehouse floors. Check the adhesive contact regularly.

Spreader no. 19, 4x4 mm : Spreading capacity approx. 1.2 kg/m²
Spreader no. 12, 6x6 mm : Spreading capacity approx. 2.0 kg/m²
Spreader no. 13, 8x8 mm : Spreading capacity approx. 2.7 kg/m²
Spreader no. 14, 10x10 mm : Spreading capacity approx. 3.5 kg/m²




Quality and guarantee

Environment and health

Safety and environment : Safety data sheets of Forbo Eurocol products according to EEG-guideline 91/155.
MSDS : For extensive information about safety and environment we refer to our website www.eurocol.nl.


Articles


ArticleDefinitionPackagingEAN-codeMin. order
795Uni-Quick25 kg bag8 710345 795012 
795Uni-Quick5x5 kg box8 710345 795029
795Uni-Quick5 kg box8 710345 7950365 pieces