• Provides very high initial tack, strong, dispersion-based adhesive for wet-set, one-side-pressure sensitive and contact bonding
• For bonding of vinyl-, CV- floor coverings in sheets, insulation mats.
• For laying on standard-compliant, fully levelled, absorbent subfloors.
• Also for laying on non-absorbent subfloors, like old vinyl floor coverings (one-side-pressure sensitive bonding) in combination with 900 Europlan DSP as membrane for migration of plasticizers out of old floors.
• Can also be used for wall covering installation.
• Can be used as contact adhesive (e.g. for heavy wall coverings, impact wall coverings in sports facilities).
• Can be thermally activated after drying.
• Castor wheel resistant according to DIN EN 12529.
• For indoor use only.
  

For bonding of

• vinyl- floor coverings in sheets,
• CV- floor coverings in sheets,
• insulation mats.

• The substrate must be pressure- and tension-resistant, permanently dry, free of cracks and dust, even and free of layers that reduce adhesion.
• Adhesion-reducing layers, old material residues must be removed by suitable mechanical measures in accordance with the specifications of DIN 18365.
• For levelling the substrate use recommended Eurocol levelling compounds/primers.
• The installation materials to be used must be suitable for the substrate and the intended use.

• Before use, temper the product according to the processing conditions.
• Stir before use!
• Depending on the type of flooring, apply the adhesive with a notched trowel to the subfloor over the entire surface and evenly without adhesive nests. The back of the flooring must be completely wetted with adhesive in scored format. Worn-out spatulas need to be replaced in time to guarantee the minimum adhesive consumption.
• Coverings must be laid in the adhesive bed which is still wet.
• The necessary flash-off time depends on the amount of adhesive (toothed strip), temperature, humidity and the absorbency of the subfloor.
  When finger-testing, the adhesive must have a soft centre, must be tacky, pull threads, but must not smear.
• Depending on the room climate and the absorbency of the substrate, the air-conditioned covering should be pushed into the adhesive bed immediately or after the flash-off time specified in the technical data, rubbed in and rolled on. Air pockets under the covering must be avoided or removed immediately.
• Head ends and non-flat covering edges must always be rolled in.
• If necessary, rub or roll the top ends, seams or other hollow areas again approx. 15 minutes after installation.

Special instructions:

Wet/one-side gluing:

• If the substrate is absorbent, allow the adhesive to flash off for approx. 10 - 15 minutes (skin formation) and lay the covering in the still relatively damp adhesive bed and rub/roll it in.
• Within the working time of approx. 30 minutes, but as a wet adhesive, lay the adhesive, rub down well immediately and roll the surface vigorously.

Pressure sensitive adhesive

• In the case of non-absorbent substrates and impermeable coverings, the adhesive must flash off completely.
• Flash-off time approx. 30 - 90 minutes depending on the room climate conditions.

Contact bonding

• Apply the adhesive to the substrate and the back of the covering and allow to dry in the same way as the pressure-sensitive adhesive.
• Within the contact bonding time of approx. 90 minutes, lay the covering and rub down well. Corrections are no longer possible!

The adhesive can be reactivated with heat within a few days. To do this, heat the covering and substrate to approx. 70 - 80°C (welding device) and carry out the bonding process in the same way as for contact bonding.

Adhesive Roll - System

• The adhesive, applied with a toothed strip, is immediately rolled out with Eurocol Microfibre Roller. This shortens the flash-off time and the tendency of coverings to indentations under early loading, as well as the marking of Scoring and the tendency to re-soiling

Working conditions: