• Elastic, conform ISO 17178, water- and solvent-free parquet adhesive based on SMP, hardens without shrinking.
• For installation of suitable on standard wooden floors like multi-layered parquet, especially surface treated parquet.
• Bonding is carried out on standard cementitious and calcium sulphate-bound screeds, on wooden composites which meet the requirements for parquet installation, fully sanded mastic asphalt, gypsum-boards suitable for installation of parquet and on Eurocol
  insulation mats (e.g. 823 Eurofloor Reno, 820/821 Eurofloor comfort, 804 Eurofloor Reno Fleece).
• Also usable on non-absorbent surfaces (e.g. fixed and cleaned ceramic and natural stone tiles, artificial stone, metals).
• Also suitable for the wood species bamboo, smoked oak.
• Easy to remove from varnished surfaces.
• Sanding and sealing after 24 - 48 hrs.
• Colouring in wood colour light brown.
• Can be applied over underfloor heating.
• For indoor use only.
• Very low VOC emission. EMICODE EC 1 Plus. 
• Emission-tested construction product according to DIBt principles.
• Declared by baubook, "ecological building product".

For installation of

• multi-layer parquet.

• The substrate must be pressure- and tension-resistant, permanently dry, free of cracks and dust, even and free of layers that reduce adhesion.
• Adhesion-reducing layers, old material residues must be removed by suitable mechanical measures in accordance with the specifications of DIN 18356.
• Old fixed floors, such as ceramic tiles, terrazzo, stone floors, metals, must be professionally cleaned and sanded matt after drying.
• Cracks or joints (except structural expansion joints) are to be closed with Eurocol grouting compounds Europlan 913 Silicate.

Recommended primers:

With this adhesive, standard-compliant parquet can also be glued directly onto non-sprinkled, specially approved Eurocol reaction resin primers or approved dispersion primers.

• When laying large-format parquet elements, it is necessary to ensure that the laying surface is even. Use levelling compounds suitable for parquet flooring.
• In case of defects, concerns must be reported in writing.

• Before use, temper the product according to the processing conditions.
• Remove any ”skin” on top of the adhesive, do not stir or mix any skin with adhesive.
• Apply the adhesive evenly to the substrate with a toothed strip adapted to the installation and the substrate roughness. If necessary, the toothed strip can be adjusted accordingly to achieve sufficient grooved back wetting. In the case of long elements, the toothed strip must be enlarged accordingly.
• When laying the parquet, do not press glue between the elements to prevent adhesive marks in the joints and prevent possible interactions with the parquet lacquer. *
• Installed materials must be immediately rolled on using a hand roller or cork rubbing board.
• Since with reaction adhesives a slight "floating" of the material to be laid cannot be avoided, the laid surface must not be walked on within the first 2 hours. If it is necessary to walk on the surface, load distribution plates must be used to avoid crushing of the adhesive.
• When working on parquet, ensure that the installed parquet is approx. 1.5 cm away from the wall.
• If necessary, the glued parquet must be weighted down during the entire setting time, especially in the case of long parquet elements.
• After a setting time of approx. 2 hours, roll the floor once again with a multi-section roller.

Sanding and sealing is possible under standard conditions after setting of the adhesive. Sanding is delayed at low temperatures, relativ humidity and high adhesive application rate by up to 2 days.

Recommended parquet finishes and oils:

The adhesive has excellent adhesion properties in combination with most types of wooden floors. Due to the large variety of wooden floors, in case of doubt, we recommend to carry out adhesive tests before processing, especially in the case of exotic woods.

Due to the elastic bonding, care must be taken to reduce side gluing when using water-based parquet sealants.

Processing conditions: 

at least 15 °C floor temperature,
at least 18°C material and room temperature,
35-75% relative humidity, recommended <65%.