Design characteristics

• Suitable for both straight and radius conveying
• up to 45 % open area for excellent air circulation
  and drainage
• Stainless steel hinge pins for high load capacity,
  lateral stiffness, fewer belt supports and minimum belt lifting in curves
• No potential belt edge catch points due to safe fixing of hinge pins

Basic data

S5-45 GRT | 45 % Opening | Grid top

• Open area (45 %) for excellent air circulation and drainage
• Lattice shaped surface

S5-45 NTP | 45 % Opening | Nub top (round studs)

• Open area (45 %) for excellent air circulation and drainage
• Lattice shaped surface with 3.0 mm (0.12 in) high round studs and 8 % contact area
• Side modules without NTP-surface

S5-39 FRT1

• Excellent air circulation and drainage
• Integrated friction pads (raised) increase surface friction and provide gentle grip
• Side modules without FRT-surface

S5-33 FRT2 | 33 % Opening | Friction top (Design 2)

• Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
• Integrated friction pads (flat) provide gentle grip

S5-45 GRT G | 45 % Opening | Grid top · guided

• Excellent air circulation and drainage
• Lattice shaped surface and Hold Down tabs
• Allows utilisation of the entire belt width

S5-45 NTP G | 45 % Opening | Nub top (round studs) · guided

• Excellent air circulation and drainage
• With round studs for increased grip (8 % contact area)
• Allows utilisation of the entire belt width
• Side modules only available without NTP-pattern

S5-39 FRT1 G | 39 % Opening | Friction top (Design 1)

• Excellent air circulation and drainage
• Integrated friction pads (raised) increase surface friction and provide gentle grip
• Allows utilisation of the entire belt width
• Side modules without FRT-surface

S5-33 FRT2 G | 33 % Opening | Friction top (Design 2)

• Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
• Integrated friction pads (flat) provide gentle grip
• Allows utilisation of the entire belt width
• Side modules without FRT-surface

S5-45 GRT RG | 45 % Opening | Grid top · reversed guided

• Excellent air circulation and drainage
• Lattice shaped surface and reversed Hold Down tabs
• Allows utilisation of the entire belt width

S5-45 NTP RG | 45 % Opening | Nub top (round studs) · reversed guided

• Excellent air circulation and drainage
• With round studs for increased grip (8 % contact area)
• Allows utilisation of the entire belt width
• Side modules only available without NTP-pattern

S5-39 FRT1 RG | 39 % Opening | Friction top (Design 1)

• Excellent air circulation and drainage
• Integrated friction pads (raised) increase surface friction and provide gentle grip
• Allows utilisation of the entire belt width
• Side modules without FRT-surface

S5-33 FRT2 RG | 33 % Opening | Friction top (Design 2)

• Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
• Integrated friction pads (flat) provide gentle grip
• Allows utilisation of the entire belt width
• Side modules without FRT-surface

S5-45 GRT ST | 45 % Opening | Grid top · strong

• Excellent air circulation and drainage
• Lattice shaped surface
• Version with reinforced brick-laid side modules (75 mm/2.9 in and 100 mm/3.9 in) increases belt pull capacity

S5-45 NTP ST | 45 % Opening | Nub top (round studs) · strong

• Excellent air circulation and drainage
• With round studs for increased grip (8 % contact area)
• Version with reinforced brick-laid side modules increases belt pull capacity
• Side modules only available without NTP-pattern

S5-39 FRT1 ST | 39 % Opening | Friction top (Design 1)

• Excellent air circulation and drainage
• Integrated friction pads (raised) increase surface friction and provide gentle grip
• Reinforced side modules increase belt pull capacity
• Side modules without FRT-surface

S5-33 FRT2 ST | 33 % Opening | Friction top (Design 2) · strong

• Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage
• Lattice shaped surface
• Version with reinforced brick-laid side modules increases belt pull capacity

Sprockets

in different sizes with round or square sprocket bore

Profiles

in different heights and designs for inclines

Side guards

in different heights for retention of bulk products

Ball-bearing modules

to minimize friction forces at the belt edge